HP LaserJet 4240/4250/4350 Fuser Assembly Exchange
Description / HP LaserJet 4240/4250/4350 Fuser Assembly Exchange
Product Information
HP RM1-1082-090CN Fuser Assembly (110-127 V) - Refurbished Exchange
Part Number: RM1-1082-090CN-RX
Condition: Refurbished Exchange. Defective core return required.
Manufacturer / Brand: HP
110 V fuser assembly for HP LaserJet 4240n / 4250 / 4350 printers. Bonds toner to paper using heat. Match the exact fuser model, revision and voltage before installation.
Technical Specifications
| Listed part number | RM1-1082-090CN-RX |
|---|---|
| Component | Fuser assembly |
| Offered part reference | RM1-1082-090CN |
| HP service-manual reference | RM1-1082-000CN |
| Voltage class | 110 V; match the printer voltage and exact fuser |
| Function | Heats and bonds the toner image to the media |
| Product grade | Refurbished Exchange |
Error Codes and Troubleshooting
These manufacturer-documented checks are suggested repair paths. Confirm the exact model, operating voltage and failed component before replacement.
| Error code / light pattern | Meaning and applicable printer models | Checks / how this part may fix it |
|---|---|---|
| 50.1 | Low fuser temperature. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| 50.2 | Fuser warmup service error. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| 50.3 | Fuser over temperature. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| 50.4 | Faulty fuser. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| 50.5 | Incorrect fuser is installed. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| 50.6 | Open fuser circuit. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn the printer off and allow the fuser to cool for at least 30 minutes before removal. Verify the correct fuser model and voltage, then reinstall it and inspect its connection to the printer. Replace a damaged connector separately. If the fault persists after these checks, the manufacturer directs fuser replacement, then the DC controller and power-supply assembly as later alternatives. Use the correct voltage replacement; this is a suggested repair path, not a guaranteed fix. |
| INSTALL FUSER | The fuser is absent or not seated correctly. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | After allowing the unit to cool for at least 30 minutes, install the matching fuser or remove and reinstall it. Push it firmly into the printer until the blue levers on both sides click into place. If the message persists, the manufacturer lists the fuser assembly, then DC controller, then power supply. A missing or unseated unit requires correct installation first. |
| 13.02.00 | Media did not pass PS103 top-of-page sensing within the specified time. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Clear actual media and scraps. Verify PS102, PS103 and PS108 sensor arms move freely, and verify PS102 installation after paper-feed service. Follow the separately listed sensor/switch checks before replacing the fuser. A fuser is a suggested repair only when diagnosis identifies its own delivery path, rollers or sensing fault; the printer sensor/switch and DC-controller alternatives remain separate. A jam code alone does not prove the fuser is defective. |
| 13.05.00 | Media did not reach fuser-delivery sensor PS108 within the specified time. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Clear actual media and scraps. Verify PS102, PS103 and PS108 sensor arms move freely, and verify PS102 installation after paper-feed service. Follow the separately listed sensor/switch checks before replacing the fuser. A fuser is a suggested repair only when diagnosis identifies its own delivery path, rollers or sensing fault; the printer sensor/switch and DC-controller alternatives remain separate. A jam code alone does not prove the fuser is defective. |
| 13.20.00 | A paper-path sensor detects media during power-on or initialization. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Clear actual media and scraps. Verify PS102, PS103 and PS108 sensor arms move freely, and verify PS102 installation after paper-feed service. Follow the separately listed sensor/switch checks before replacing the fuser. A fuser is a suggested repair only when diagnosis identifies its own delivery path, rollers or sensing fault; the printer sensor/switch and DC-controller alternatives remain separate. A jam code alone does not prove the fuser is defective. |
| 13.06.00 | A page is jammed near the rear output door. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Clear the jam and inspect PS106 paper-width and PS108 fuser-delivery sensor arms for free movement. Remove torn scraps from the duplexer. The manufacturer lists the media-size sensor and fuser as repair steps. Power off, remove the duplexer and retest to isolate its effect; an error that persists can require DC-controller repair. Replace this fuser only when its own fault is confirmed. |
| 13.12.00 | A page is jammed near the rear output door. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Clear the jam and inspect PS106 paper-width and PS108 fuser-delivery sensor arms for free movement. Remove torn scraps from the duplexer. The manufacturer lists the media-size sensor and fuser as repair steps. Power off, remove the duplexer and retest to isolate its effect; an error that persists can require DC-controller repair. Replace this fuser only when its own fault is confirmed. |
| 13.1C.00 | Fuser-area jam; paper is probably wrapped around a fuser roller. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | Turn power off and allow the fuser to cool for at least 30 minutes before removal. Remove the fuser and turn the blue knob to release the wrapped paper. Remove all scraps. Replace the matching fuser if necessary after inspecting it for the confirmed fault. |
| 41.3 | Unexpected media size in the indicated tray. HP LaserJet 4240n / 4250 / 4350; exact fuser model and voltage must match the installed printer. | First correct paper size and tray configuration. Verify that PS102, PS103 and PS108 operate and their flags move freely. A fuser-delivery sensing problem must be distinguished from the other printer sensors; the manufacturer next lists the DC controller. This code alone does not direct automatic fuser replacement. |
Other Symptoms This Part May Fix
- Loose toner or toner that smears after printing: Check media surface/quality, contamination and fuser-mode settings first, and run a printer cleaning page. A fuser that does not heat sufficiently may fail to bond toner to paper; HP lists fuser replacement for that confirmed defect. The DC controller also regulates fuser temperature and can be a separate cause.
- Lines, white lines or smudged lines traced to the fuser: Run cleaning pages where directed. A worn or persistently dirty fuser roller, defective fuser film or confirmed damaged fuser can require replacement. Check cartridge condition, laser-path/cable faults, static-eliminator contamination and other paper-path rollers as applicable; these symptoms do not identify the fuser by themselves.
- Repeated marks at the fuser interval: Measure the spacing between defects and compare it with the manufacturer repetitive-defect ruler. The table identifies fuser intervals of 75.0 mm (2.95 in) and 94.0 mm (about 3.7 in), while the cartridge drum is 94.2 mm. The detailed note attributes 94.0 mm particularly to the 4300 fuser; do not treat that near-match as proof for this 4250/4350-style unit. Clean/test and positively identify the defective component before replacement.
- Specks traced to worn fuser rollers: Check printer cleanliness, media and the print cartridge first. HP lists worn fuser rollers as another cause of specks and directs fuser replacement when that wear is confirmed. Dots can instead arise from static-eliminator, transfer-roller or power-supply faults.
- Paper wrinkles or folds at the paper-path exit: Inspect the exact damage location. HP lists fuser replacement for a dirty fuser inlet guide; for a dirty or damaged pressure roller, run cleaning pages first and replace the fuser if the fault persists. Wrinkling at the path entrance can instead involve feed/registration rollers, debris, cartridge shutter or registration unit.
- Dropouts, curl or wave that require settings/cleaning checks: Check media quality, storage, print side, tray loading, environment and output route. A dirty fuser roller can require cleaning pages for dropouts; incorrect fuser mode can cause curl/wave and should be corrected for the media. These conditions are not automatic reasons to order a new fuser.
Maintenance / Replacement Cycle
Maintenance and Service Life
HP lists 225,000 pages as the original 4250/4350 fuser planning interval. Actual service depends on media, usage and component condition; this is not a guaranteed life for the offered unit. Inspect the fuser during diagnosis and scheduled service. Replacing a fuser alone does not complete every item in the printer maintenance kit.
Before removal, turn printer power off and allow the fuser to cool for at least 30 minutes. Remove the rear output bin, squeeze the blue fuser-release tabs and pull the unit straight back. Avoid dropping or jarring it. On installation, make sure both sides snap fully into place.
Used In Products
Warranty
90 days, provided by seller
More Information
| Manufacturer | HP |
|---|---|
| Condition | Refurbished |
| Part Number | RM1-1082-090CN-RX |
| OEM Part Number | RM1-1082-090CN |
| Alternate Part Numbers | RM1-1082-090CN, RM1-1082-070CN, RM1-1082-000CN |
| Weight | 6.000000 |