HP LaserJet 4300 Fusing Assembly RM1-0101-000CN Refurbished
Description / HP LaserJet 4300 Fusing Assembly RM1-0101-000CN Refurbished
Product Information
HP LaserJet 4300 Fusing Assembly
Part Number: RM1-0101-000CN-RO
Condition: Refurbished Outright. No core return required.
Manufacturer / Brand: HP
110-127 V fuser assembly for the HP LaserJet 4300 series. The assembly bonds the toner image to the print media using heat and pressure.
Technical Specifications
| Component type | Fuser / fusing assembly |
|---|---|
| Listed part number | RM1-0101-000CN-RO |
| Electrical rating | 110-127 V |
| Printer family | HP LaserJet 4300 series |
| HP service reference | RM1-0101-000CN / RM1-0101-200CN |
| Alternate catalog part numbers | RM1-0101-300CN, Q2431-69018 |
| Function | Bonds toner to paper using heat and pressure |
Error Codes and Troubleshooting
These manufacturer-documented checks are suggested repair paths. A code can have several causes; confirm the printer model, voltage and failed component before ordering.
| Error code / light pattern | Meaning and applicable printer models | Checks / how this part may fix it |
|---|---|---|
| 50.1 FUSER ERROR | Low fuser temperature HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 50.2 FUSER ERROR | Fuser warm-up service error HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 50.3 FUSER ERROR | Fuser over-temperature HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 50.4 FUSER ERROR | Faulty fuser HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 50.5 FUSER ERROR | Incorrect fuser installed HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 50.6 FUSER ERROR | Open circuit in fuser HP LaserJet 4300 series. | Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains. |
| 13.02.00 JAM IN TOP COVER AREA | Paper did not pass the top-of-page sensor PS103 in time. HP LaserJet 4300 series. | Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser. |
| 13.05.00 JAM IN TOP COVER AREA | Paper did not reach the fuser-delivery sensor PS108 in time. HP LaserJet 4300 series. | Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser. |
| 13.20.00 JAM IN TOP COVER AREA | Paper was detected at power-on or initialization by PS102, PS103 or PS108. HP LaserJet 4300 series. | Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser. |
| 13.21.00 JAM IN TOP COVER AREA | The top-cover switch SW101 opened during printing or may be defective. HP LaserJet 4300 series. | Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser. |
| 13.06.00 JAM INSIDE REAR DOOR | A jam occurred in the rear delivery area. HP LaserJet 4300 series. | Clear jammed media; inspect paper-width sensor PS106 and fuser-delivery sensor PS108 for freely moving flags. Check for scraps in the duplexer. HP lists PS106 and fuser replacement in the repair path. To isolate the duplexer, switch off, remove it, and switch on again; continue with dc-controller diagnosis if the problem persists. |
| 13.12.00 JAM INSIDE REAR DOOR | A jam occurred in the rear delivery area. HP LaserJet 4300 series. | Clear jammed media; inspect paper-width sensor PS106 and fuser-delivery sensor PS108 for freely moving flags. Check for scraps in the duplexer. HP lists PS106 and fuser replacement in the repair path. To isolate the duplexer, switch off, remove it, and switch on again; continue with dc-controller diagnosis if the problem persists. |
| 13.1C.00 FUSER JAM | Media is wrapped around the fuser roller. HP LaserJet 4300 series. | Switch off and allow at least 30 minutes for the fuser to cool before removal. Remove the fuser and turn its blue knob to release trapped media. Replace the fuser if necessary; remove all scraps before reinstallation. |
| 41.3 UNEXPECTED SIZE IN TRAY XX | Loaded media is longer or shorter than the configured tray size. HP LaserJet 4300 series. | Correct the media size/type and verify tray settings on a configuration page first. Check PS102, PS103 and fuser-delivery sensor PS108 operation and free flag movement. A fuser-area obstruction or damaged delivery flag needs correction; this message alone does not justify buying a fuser. HP next lists the dc controller PCA if the fault persists. |
Other Symptoms This Part May Fix
- Wrinkles at the paper-path exit: Inspect the fuser inlet guide and pressure roller. A dirty inlet guide can require fuser replacement. Run cleaning pages for a dirty pressure roller; replace the fuser if the condition persists. Input-side wrinkles can instead originate in registration or feed rollers.
- Toner smears or rubs off: Check media quality and fuser-mode settings and run cleaning pages. A defective fuser that does not heat sufficiently is a documented replacement path; the dc controller can also be responsible.
- Specks or dots: Check the print cartridge, media and interior contamination. Worn fuser rollers are one documented cause that can require fuser replacement.
- Dropouts or character voids: Check the paper side, media, environment, cartridge, density and EconoMode. Clean a dirty fuser using cleaning pages and check the fuser-mode setting before replacing parts.
- Vertical or horizontal lines: Check the cartridge and laser path first. Clean a dirty fuser; replace it if lines persist. Damaged fuser film is a documented cause of horizontal lines.
- Repeating defects or ghost images: Measure the repeat spacing and inspect the cartridge before choosing a part. HP identifies fuser repeats at 75.0 mm and 94.0 mm; 94.0 mm is specifically associated with the LaserJet 4300 fuser roller and is close to the cartridge drum repeat. Run cleaning pages; replace the fuser only when the defect is traced to it.
- White lines or smudged lines: Inspect the cartridge, laser path and paper path. Clean the fuser and replace it if the diagnosed fuser defect persists; contamination or damage elsewhere must also be checked.
- Curl or wave: Check media storage, room conditions, output bin and fuser-mode setting first. A setting change or different media/output path may correct curl without replacing the fuser.
Maintenance / Replacement Cycle
HP lists a 200,000-page expected component life and printer-maintenance interval for the original LaserJet 4200/4300 fuser. This is a service-planning reference, not a guaranteed yield for this replacement.
Run a cleaning page when replacing the print cartridge. Use copier-grade paper and select CONFIGURE DEVICE > PRINT QUALITY > CREATE CLEANING PAGE; follow the printed instructions. With a duplexer installed, open the rear output bin before cleaning and close it afterward. Automatic cleaning applies only without the optional duplexer; HP recommends 2,000 pages or less.
Switch off and allow at least 30 minutes for cooling before removing the fuser. Squeeze the blue release tabs and pull it straight out; fully seat the replacement until both sides snap into place. Reset the maintenance counter only after installing the complete maintenance kit.
Used In Products
Warranty
90 days, provided by seller
Compatible Printer Models
More Information
| Manufacturer | HP |
|---|---|
| Condition | Refurbished |
| Part Number | RM1-0101-000CN-RO |
| OEM Part Number | RM1-0101-000CN |
| Alternate Part Numbers | RM1-0101-000CN, RM1-0101-300CN, Q2431-69018 |
| Weight | 3.200000 |