HP LaserJet 4345 Tray 1 Solenoid

All items come with standard warranty of 90 days, warranty provided by seller.

In stock

Only 23 left

Part Number
RK2-0276-000CN-RO
$8.00

Description / HP LaserJet 4345 Tray 1 Solenoid

Product Information

HP RK2-0276-000CN Tray 1 Pickup Solenoid SL102 - Refurbished Outright

Part Number: RK2-0276-000CN-RO

Condition: Refurbished Outright. No core return required.

Manufacturer / Brand: HP

Pickup solenoid SL102 for Tray 1. Match the exact part and pickup position before ordering. Diagnosis must distinguish a failed solenoid from worn rollers, sensing faults or a damaged pickup mechanism.

Technical Specifications

Listed part numberRK2-0276-000CN-RO
ComponentTray 1 pickup solenoid
HP service referenceRK2-0276-000CN
Solenoid designationSL102
4250/4350 diagnostic connectionJ79 at the DC controller; approximately 110 ohms on the cable side
Printer familiesHP LaserJet 4240n / 4250 / 4350; HP LaserJet M4345 MFP

Commonly Used to Fix

These manufacturer-documented checks are suggested repair paths. Confirm the exact model, operating voltage and failed component before replacement.

Error code / light patternMeaning and applicable printer modelsChecks / how this part may fix it
13.01.00Media did not arrive at the pre-feed sensor PS102 within the specified time.
HP LaserJet 4240n / 4250 / 4350; diagnose the actual Tray 1 pickup solenoid SL102.
Clear the actual jam and verify media loading and sensing first. Inspect the pickup/feed/separation rollers and replace confirmed worn parts before condemning the solenoid. For a pickup fault traced to Tray 1, turn printer power off and disconnect the pickup-solenoid connector at DC-controller J79. For the 4250/4350, measure approximately 110 ohms between the cable-side connectors; replace the solenoid if this test fails. Do not substitute the approximately 160 ohm test for the older 4200/4300. A damaged pickup drive, feed clutch, lifter/stack sensor or DC controller needs separate diagnosis.
13.03.00Media did not arrive at the top-of-page sensor PS103 within the specified time.
HP LaserJet 4240n / 4250 / 4350; diagnose the actual Tray 1 pickup solenoid SL102.
Clear the actual jam and verify media loading and sensing first. Inspect the pickup/feed/separation rollers and replace confirmed worn parts before condemning the solenoid. For a pickup fault traced to Tray 1, turn printer power off and disconnect the pickup-solenoid connector at DC-controller J79. For the 4250/4350, measure approximately 110 ohms between the cable-side connectors; replace the solenoid if this test fails. Do not substitute the approximately 160 ohm test for the older 4200/4300. A damaged pickup drive, feed clutch, lifter/stack sensor or DC controller needs separate diagnosis.
13.XX.YY JAMManufacturer grouped pickup/feed jam pattern; apply only to a fault isolated to this solenoid.
HP LaserJet 4240n / 4250 / 4350; diagnose the actual Tray 1 pickup solenoid SL102.
Clear the actual jam and verify media loading and sensing first. Inspect the pickup/feed/separation rollers and replace confirmed worn parts before condemning the solenoid. For a pickup fault traced to Tray 1, turn printer power off and disconnect the pickup-solenoid connector at DC-controller J79. For the 4250/4350, measure approximately 110 ohms between the cable-side connectors; replace the solenoid if this test fails. Do not substitute the approximately 160 ohm test for the older 4200/4300. A damaged pickup drive, feed clutch, lifter/stack sensor or DC controller needs separate diagnosis.
13.JJ.NT JAM IN TRAY 1Tray 1 jam; the MP-tray pickup solenoid might be defective.
HP LaserJet M4345 MFP only; Tray 1 pickup solenoid SL102.
Remove the jammed media and follow the onscreen instructions. If the message persists, open Administration > Troubleshooting > Component Test and run MP Tray Solenoid. If the solenoid is defective, replace it. Inspect loading and the pickup mechanism first; this is a suggested repair after a failed component test, not a guarantee from the code alone.

Other Symptoms This Part May Fix

  • Pickup timing or actuation failure traced to Tray 1 solenoid SL102: On the 4250/4350, follow the manufacturer J79 cable-side resistance test after inspecting rollers, wiring and the actual pickup mechanism. On the M4345 MFP, this solenoid activates the corresponding pickup roller; use Administration > Troubleshooting > Component Test to observe or listen to the selected component. A feed-roller clutch, worn roller, sensing fault or damaged drive requires its own repair. Do not replace this solenoid solely because a paper-jam message appears.

Used In Products

HP LaserJet 4240n
HP LaserJet 4250 series
HP LaserJet 4350 series
HP LaserJet M4345 MFP

Warranty

90 days, provided by seller

More Information

Manufacturer HP
Condition Refurbished
Part Number RK2-0276-000CN-RO
OEM Part Number RK2-0276-000CN
Alternate Part Numbers RK2-0276-000CN, RK2-0277-000CN
Weight 1.000000
Write Your Own Review
You're reviewing: HP LaserJet 4345 Tray 1 Solenoid

This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.

✓ FREE SHIPPING on Printer Parts Orders over $100 and Specified Toners within the continental USA